Updated November 2026

The NordicTrack X24 Incline Trainer Treadmill is a folding-deck, incline-capable home treadmill that owners use for walking, jogging and incline training. This guide walks you through the setup steps, how to use the incline and speed controls safely, and the maintenance habits that keep the deck and motor running smoothly. Use it as a practical starting point, then check the owner’s manual that came with your unit for model-specific details.

Set Up the X24 Safely Before the First Workout

Placement matters more than most first-time owners expect. Manufacturers generally specify a clear area around the treadmill so you can step on and off without twisting, and a level, stable floor. Plug the unit into a grounded outlet rather than a shared extension cord, since a dedicated circuit reduces the risk of nuisance trips and overheating.

Shopping for one? See our guide: 6 Best Folding Treadmills with Auto Incline for Home (2026).

  1. Unpack the unit and confirm all hardware, the safety key (clip-style) and the console cable are present.
  2. Assemble the upright and console following the diagram in the manual, tightening all bolts by hand first, then with the supplied tools.
  3. Level the frame using the leveling feet until the deck sits flat and does not rock.
  4. Attach the safety key to your clothing before pressing Start, so the belt stops if you fall.

Use the Incline and Speed Controls

The X24’s incline range is controlled from the console, and the belt speed is adjusted separately. Start at a low incline and a walking pace until you understand how the controls respond. Many owners find it helpful to change only one variable at a time: hold speed steady while you raise the incline in small steps, then reverse the process to finish.

Working Through a First Incline Session

Begin with a 5-minute warm-up at 0% incline and a brisk walking speed. Raise the incline by one or two levels, then keep it there for 5 to 10 minutes while you maintain a comfortable pace. Lower the incline back to 0% for a 3-minute cooldown. Keep your posture upright and avoid gripping the handrails, which reduces the effort your legs and core actually do.

Calibrate and Check Readings

If the displayed incline or speed seems off compared to what you feel, calibration is worth checking. The exact calibration steps depend on the firmware and model revision, so follow the procedure in your manual. For a general overview of the process, see Nordictrack Treadmill Incline Calibration: Step-by-Step Guide (2026). Remember that calorie and distance readings on any treadmill are estimates, not lab measurements.

Maintenance That Protects the Deck and Motor

Routine care is inexpensive in time and effort. Wipe the console and handrails after each session, keep the area under the deck free of dust, and inspect the belt for fraying or uneven tension. Owners often report that the belt drifts toward one side over time; if it does, adjust the rear roller bolts a quarter turn at a time, following the manual’s tensioning procedure. If the incline stops responding or makes grinding noises, stop using the unit and review the troubleshooting section of your manual before continuing.

Common Mistakes

  • Running on an unlevel floor, which can cause the belt to track poorly and wear unevenly.
  • Jumping straight to high incline levels without a warm-up at 0%.
  • Skipping the safety key, which removes the automatic stop if you lose your footing.
  • Holding the handrails tightly, which makes the workout easier than intended and skews calorie estimates.
  • Ignoring belt drift or a squealing sound instead of adjusting tension early.
  • Treadmill floor mat: Protects flooring from vibration and dust under the unit. View on Amazon
  • Treadmill lubricant: Used on the deck according to the manufacturer’s instructions for models that require it. View on Amazon
  • Hex key set: Handy for tightening frame bolts during assembly and belt adjustment. View on Amazon

FAQ

Do I need to lubricate the X24 deck?

Some treadmill models require periodic deck lubrication and others do not. Check your owner’s manual for the specified product and interval before applying anything.

Why does the incline seem to lag behind the setting?

Incline motors take a few seconds to reach a new position, so a short delay is normal. If the lag is long or the incline stops partway, review the troubleshooting guidance for your model.

How often should I check belt tension?

Check it periodically, especially if you notice the belt slipping or drifting to one side. Make small adjustments and test at a slow speed before resuming a full workout.

Conclusion

With a level setup, a careful warm-up and a few minutes of routine care, the NordicTrack X24 can handle everyday walking and incline training well. Keep the owner’s manual nearby for model-specific steps. If something still seems wrong after checking the basics, consult a qualified service technician.

Caleb Morgan

About Caleb Morgan

Caleb Morgan is part of our editorial team and reviews and edits our treadmills & walking pads guides, checking product details against manufacturer specifications and owner feedback.